The Purple Professional Aura Sensor 48W is designed for the professional catalysis of gels, semi-permanent nail polishes and other nail products compatible with UV/LED technology.

Equipped with 30 UV+LEDs and a power of 48W , it works with wavelengths of 365 and 405 nm to provide adequate coverage of the photoinitiators commonly used in different professional systems.

Its motion sensor allows operation to start automatically when a hand is inserted, while the built-in timers allow different working times to be selected according to the needs of the product used.

30 UV+LEDs and 48W of power

The Aura Sensor incorporates 30 UV+LED light points distributed inside the lamp and a power of 48W.

Its technology combines wavelengths of 365 + 405 nm , allowing it to work with products formulated for UV/LED catalysis.

Motion sensor

The motion sensor makes daily work easier by detecting the insertion of a hand and automatically activating the lamp.

When used by the sensor without first selecting one of the timers, the lamp starts an automatic cycle with a maximum operating time of 120 seconds .

30, 60 and 99 second timers

Aura Sensor allows you to directly select cycles of:

• 30 seconds.
• 60 seconds.
• 99 seconds.

The selected time is displayed on its LED screen, making it easy to control the catalysis during service.

Low heat mode

When the lamp is automatically activated by the sensor without selecting a timer, the first 50 seconds of the 120-second cycle operate in low heat mode .

This function allows for a more progressive initial polymerization, which is especially useful when working with certain construction products.

Key advantages

• Professional UV/LED lamp.
• 48W of power.
• 30 UV+LED LEDs.
• Dual wavelength: 365 + 405 nm.
• Motion sensor.
• Automatic ignition upon insertion of hand.
• 30, 60 and 99 second timers.
• Automatic cycle of up to 120 seconds using a sensor.
• Low heat mode for the first 50 seconds of the automatic cycle.
• LED display for viewing the time.
• Designed for professional use.
• Power adapter included.
  
  

Is it for you?

Yes, if you're looking for a UV/LED lamp to work regularly with professional nail systems and want to combine 48W power with an automatic sensor and different curing times.

This might be especially suitable if you work with semi-permanent nail polish, base coats, builder gels, acrygel, or UV/LED top coats and need a versatile lamp for different phases of the service.

It is also practical for continuous work in the salon: the sensor avoids having to manually activate the lamp each time it is used, and the different timers allow you to adapt the cycle to the product you are using.

Instructions for use

1. Connect the power adapter to the lamp and a suitable electrical outlet.
2. Apply the UV/LED product following its specific instructions.
3. Insert your hand correctly into the lamp.
4. Select, where appropriate, the 30, 60 or 99 second timer.
5. The selected time will appear on the LED screen.
6. The motion sensor can also be used without first selecting a timer. In this case, the lamp automatically starts a cycle of up to 120 seconds.
7. Remove your hand once the catalysis time indicated for the product used has been completed.
   
   

Professional advice

The wattage of a lamp alone does not determine the correct curing time. Always respect the curing time indicated by the manufacturer of the gel, base coat, polish, or Top Coat you are using.

Place your hand flat and centered inside the lamp , avoiding lifting your fingers. Pay special attention to your thumb: an incorrect position can cause it to receive the light at a different angle than the rest of your nails, resulting in uneven curing.

When working with construction products that may generate a feeling of heat during polymerization, the low heat mode can be especially useful for achieving a more gradual catalysis.

Also keep the inner surface and LEDs clean. Accumulated gel or product residue can interfere with the lamp's proper functioning and is much more difficult to remove once fully catalyzed.

Technical specifications

• Brand: Purple Professional .
• Model: Aura Sensor.
• Type: Professional UV/LED nail lamp.
• Power: 48W.
• Number of LEDs: 30 UV+LED.
• Wavelength: 365 + 405nm.
• Timers: 30 / 60 / 99 seconds.
• Motion sensor: Yes.
• Automatic cycle via sensor: Up to 120 seconds.
• Low heat mode: Yes, for the first 50 seconds of the automatic cycle.
• LED display: Yes.
• Dimensions: 208 x 185 x 97 mm.
• Voltage: 100-240 V ~ 50-60 Hz.
• Included accessory: Adapter.
• Use: Professional.
  
  

Conservation and maintenance

Keep the lamp clean and dry. If any product spills inside, clean it following the equipment maintenance recommendations and taking care not to damage the electrical components or LEDs.

Disconnect the equipment from the power supply before performing cleaning tasks and avoid direct contact of the adapter or electrical components with liquids.

Why choose Aura Sensor 48W?

Because it brings together the most useful functions for daily professional work: 48W of power, 30 UV+LEDs, dual wavelength, automatic sensor, different timers and low heat mode .

Its combination of automatic operation and manual time selection allows the lamp to be adapted to different products and protocols, facilitating a more comfortable and controlled work in professional manicures.